Skip to main content

What is pile integrity test for concrete piles | Low Strain Integrity Test |

A pile is a slender element cast in the ground or driven into it. Since pile construction as well as the final product are mostly invisible, engineers have often questioned their integrity, i.e. their compliance with project drawings and specifications. In fact, experience [1] has shown that in piles, of all kinds flaws may occur. The purpose of integrity testing is to discover such flaws before they can cause any damage.

Historically, pile integrity was investigated by direct methods.[2] These included external methods such as excavation around the pile and internal or intrusive methods, such as core-drilling . While excavation may be effective in exposing flaws in the outer part of the pile, it is usually limited to a depth of a few meters. Core drilling, on the other hand, can be carried out to a large depth provides full information, but only for a very small fraction of the pile volume.


Indirect methods, or imaging, were first developed in the early 1970s. These include three distinct methods:

  • Nuclear radiation, or gamma-gamma method[3]
  • Short wave (ultrasonic) acoustic method[4]
  • Long wave (sonic) acoustic method[5]


A pile integrity test (also known as low-strain dynamic test, sonic echo test, and low-strain integrity test) is one of the methods for assessing the condition of piles or shafts. It is cost-effective and not very time-consuming.


Pile integrity testing using low-strain tests such as the TDR (Transient Dynamic Response) method, is a rapid way of assessing the continuity and integrity of concrete piled foundations.

The test measures:

  • pile length, or depth to anomalies
  • pile head stiffness
  • pile shaft mobility, which is dependent on pile section and concrete properties


The software also produces computer simulations and impedance profiles of the test result, to analyze in detail any intermediate pile shaft responses.


The TDR test requires minimal of preparation and is able to find defects corresponding to cracks, reductions in section and zones of poor quality concrete


The test is based on wave propagation theory. The name "low-strain dynamic test" stems from the fact that when a light impact is applied to a pile it produces a low strain. The impact produces a compression wave that travels down the pile at a constant wave speed (similarly to what happens in high strain dynamic testing). Changes in cross sectional area - such as a reduction in diameter - or material - such as a void in concrete - produce wave reflections.


This procedure is performed with a hand held hammer to generate an impact, an accelerometer or geophone placed on top of the pile to be tested to measure the response to the hammer impact, and a data acquisition and interpretation electronic instrument.


The test works well in concrete or timber foundations that are not excessively slender. Usually the method is applied to recently constructed piles that are not yet connected to a structure. However, this method is also used to test the integrity and to determine the length of piles embedded in structures. Widely used in Australia now on existing structures.


This method is covered under ASTM D5882-16 - Standard Test Method for Low Strain Integrity Testing of Piles. IS 14893 (2001)

Watch Video: 


Labels:

Comments

Post a Comment

Popular posts from this blog

Ultrasonic pulse velocity test for concrete

  Introduction An  ultrasonic pulse velocity (UPV) test  is an  in-situ ,  nondestructive  test to check the quality of  concrete  and natural rocks. In this test, the strength and quality of concrete or rock is assessed by measuring the velocity of an  ultrasonic pulse  passing through a concrete structure or natural rock formation. Ultrasonic Pulse Velocity (U.P.V) This test is conducted by passing a pulse of ultrasonic through concrete to be tested and measuring the time taken by pulse to get through the structure. Higher velocities indicate good quality and continuity of the material, while slower velocities may indicate concrete with many cracks or voids Ultrasonic testing equipment includes a pulse generation circuit, consisting of electronic circuit for generating pulses and a transducer for transforming electronic pulse into mechanical pulse having an oscillation frequency in range of 40 kHz to 50 kHz, and a pulse rece...
Post a Comment
Read more

What is the rebound hammer test? Object, Principle, Apparatus, Procedure, Influence and Interpretation of results

  Importance and Rebound Hammer Test : It is often necessary to test concrete structures after the concrete has hardened to determine whether the structure is suitable for its proposed structure. Such testing should ideally be done without damaging the structure, which is called a Non-destructive Test on concrete. Rebound Hammer is one of the methods of testing for the strength of concrete . Rebound hammer is used for checking the compressive strength of concrete (as per IS-13311(Part-2)/92 ) at a certain age of concrete. Rebound Hammer Test The object of the test : i) assessing the likely compressive strength of concrete with the help of suitable correlations between rebound index and compressive strength,  ii) assessing the uniformity of concrete, iii) assessing the quality of the concrete in relation to standard requirements, and iv) assessing the quality of one element of concrete in relation to another. NOTE - The rebound hammer method can be used with greater confidence...
Post a Comment
Read more

Profometer Test ( Rebar Locator Test ) | Lab Test Procedure | Applications, Advantages and Disadvantages

  Non-destructive tests on concrete can be understood as the type of test on concrete structures that are employed to measure the strength of the concrete without actually destroying the structure. The primary objective of such a test is to evaluate the strength and durability of the existing concrete structure as well as for the identification of cracks and defects. One such type of non-destructive test on concrete structures is the Profometer test. ** Fast and accurate rebar detection , cover and diameter size measurement Profometer test can be defined as the non-destructive test conducted on the concrete structures to determine the size and location of the reinforcements and  concrete  cover rapidly and efficiently. This test is also commonly known as the rebar locator test. The instrument used to conduct this test is known as profometer or rebar locator. The rebar locator test is the fastest and the easiest method of detecting the reinforcement bars in concrete. The ...
Post a Comment
Read more